Useful information
SOLAR HEATERS ΗΛΙΟΑΚΜΗ (MEGASUN)
Information, troubleshooting, magnesium rod replacement, daily hot water consumption
Useful information
Which solar water heater to choose (hot water consumption table)
The solar water heater will reach optimum performance two days after the installation. During these two days, it is recommended to avoid hot water consumption, even if there is sunshine.
- Check every year the level of the fluid in the closed circuit.
- In regions with a lot of dust, we recommend that you clean the glass of the collector with water, every two months in order to remove the dust from the glass, unless there is enough rain.
- In case of glass damage, replace the glass immediately to avoid further damage of the collector.
- For all water heaters, the main principles and codes require that the function of the valves is checked once a year. We also recommend that during the same period you check the screws, nuts, plates, moly plugs, screw nuts and support plates, for looseness or any damages, especially when the appliance is installed near the sea. In case of damages, they must be replaced by owner’s expenses.
- During a long absence (such as summer holidays), it is recommended to cover the collector(s) with an opaque cover.
- Once the storage tank is filled in with water, it must not get empty (evacuated) for many hours, and only if there is a need for changing the magnesium rod or the electrical resistance for which it is required a short time, since there is the possibility of creating cracks and detachments in the internal protection of the storage tank.
- The working pressure of the system is 7 Bar. In areas where the water supply pressure exceeds 6 Bar it is necessary to fit a pressure reducer.
IF THE SOLAR HEATER DOESN’T SUPPLY HOT WATER WITH THE SUN
- Check carefully all the connections of the solar water heater for leaks.
- Check the fluid level in the closed circuit and fill it, if necessary (see instructions, page 16).
- Check the connection tubes (05) and (18) to ensure that they are not bented or twisted.
- Ensure that there is no air trapped inside the collector and the storage tank.
- Ensure that the solar water heater is installed in horizontal position.
- Ensure that the supply of hot water is not connected to a supply of cold water.
- Check the plumbing piping of your house as well as the taps for slow leaks.
- Ensure that the storage tank’s and collector’s connections are properly made and they are fully water tight.
- Ensure that there is no obstacle (building, tree etc) shading the solar water heater, or any part of it.
- If there is a mixing valve for hot / cold water in the outlet of the boiler, please check that it is correctly adjusted and it is functioning. The following should be also taken into consideration:
- The consumption of hot water is bigger than the appliance’s capacity.
- Weather conditions.
- Huge consumption of hot water during the night.
- The customer didn’t understand the use of the electric resistance.
- Customer’s expectations about the performance of the system. If your solar water heater continues not to supply hot water, contact your local distributor.
IF THE SOLAR WATER HEATER DOESN’T SUPPLY HOT WATER WITH THE ELECTRIC RESISTANCE
- Turn off the power supply and remove the resistance’s cover.
- Check the safety thermal switch F on the thermostat, which has to be pushed in.
- Check the wiring between the thermostat and the electric resistance.
- Check if the thermostat is adjusted in a lower temperature than the desired one.
- Check the resistance for any damage.
- Check the main power supply.
- Turn the power supply on and check if the electric wires are properly connected to the relevant poles of the resistance. A certified electrician must do all the electrical connections and checkings.
Τo replace the magnesium rod:
- Turn the power supply off.
- Empty the water from the storage tank.
- Remove the electric resistance and unbolt the old worn magnesium rod and fix the new one. Fix afterwards the electric resistance after you have checked that the elastic flange is not worn-out. If the elastic flange is wornout, replace it with a new one.
- Turn on the water supply and check that the tank is completely water tight.
- After the tank is completely filled, switch on the main power supply